These are the pdms piping commands which are used to model the piping in e3d. With the help of these E3d piping commands users can easily model the piping in e3d software. These are below mention the e3d piping commands are easy to use.
pdms piping commands
| COMMAND | EXPANSION OF COMMAND |
| DELETE BRAN | DELETE BRANCH |
| Q HSTU | TO DISPLAY BRANCH HEAD SIDE TUBE ATTRIBUTES |
| Q LSTU | TO DISPLAY COMPONENT LEAVE SIDE TUBE ATTRIBUTES |
| Q ABORE | TO DISPLAY ARRIVE BORE OF A COMPONENT |
| Q LBORE | TO DISPLAY LEAVE SIDE BORE OF A COMPONENT |
| ADD HREF TREF | ADD HEAD & TAIL REFERENCE |
| Q HBORE | TO DISPLAY THE HEAD SIDE BORE OF A BRANCH |
| Q TBORE | TO DISPLAY THE TAIL SIDE BORE OF A BRANCH |
| Q SPRE | TO DISPLAY THE SPECIFICATION OF THE COMPONENT |
| Q PSPEC | TO DISPLAY THE SPECIFICATION OF THE PIPE |
| NEW ELBO CHOO | CREATE NEW ELBO |
| NEW ELBO SEL WITH STYP EA | TO CREATE THE ELBO WITH SPECIFIC SELECTION TYPE |
| AXES AT HPOS | AXES AT HEAD POSSITION OF THE BRANCH |
| AXES AT TPOS | AXES AT TAIL POSSITION OF THE BRANCH |
| NEX TUBI | ASKING FOR TUBE BEING ON THE COMPONENT |
| Q ITLE | TO DISPLAY THE LENGTH OF THE TUBE BETWEEN TWO COMPONENTS |
| Q HREF | TO DISPLAY THE HEAD REFERENCE OF A BRANCH |
| Q TREF | TO DISPLAY THE TAIL REFERENCE OF A BRANCH |
| Q DIR | TO DISPLAY THE DIRECTION OF THE SELECTED COMPONENT |
| CONN PH TO FIR MEM | CONNECT BRANCH HEAD TO THE FIRST MEMBER OF THE BRANCH |
| CONN PT TO LAS MEM | CONNECT THE BRANCH TAIL TO THE LAST MEMBER OF THE BRANCH |
| Q ORI | TO DISPLAY THE ORIENTATION OF SELECTED COMPONENT |
| DIST | GIVING THE DISTANCE BETWEEN TWO COMPONENT CENTERS |
| CLEA (SPOOL) | GIVING THE SPOOL DISTANCE BETWEEN TWO COMPONENTS |
| Q CATREF | TO DISPLAY THE CATALOGUE REFERENCE AT COMPONENT LEVEL |
| CONN | CONNECT |
| FCONN | FORCE CONNECT |
| Q STYP | TO DISPLAY THE COMPONENT SELECTION TYPE |
| Q DTXR | TO DISPLAY THE DETAIL TEXT(DESCRIPTION OF THE COMPONENT |
| DRAG BY E 1000 | STRECH THE COMPONENT BY EAST 1000 (NOT PREFERED) |
| Q MTXX | TO DISPLAY THE MATERIAL OF THE COMPONENT |
| Q MODE | TO DISPLAY THE MODE OF DIRECTION (FOR/BACK) |
| FOR | TO SET THE FORWARD MODE |
| BACK | TO SET THE BACKWARD MODE |
| FIRST MEM | TO NAVIGATE THE FIRST MEMBER |
| LAST MEM | TO NAVIGATE THE LAST MEMBER |
| FIRST FLAN | TO NAVIGATE THE FIRST FLANGE IN HIERARCHY |
| Q PARA | TO DISPLAY THE PARAMETERS |
| Q ACONN | TO DISPLAY THE ARRIVE CONNECTION DETAIL OF A COMPONENT |
| Q LCONN | TO DISPLAY THE LEAVE CONNECTION DETAILS OF A COMPONENT |
| DIR TOW NEX | DIRECTION TOWARDS THE NEXT COMPONENT |
| Q REF | TO DISPLAY REFERENCE |
| INCL | INCLUDE |
| ORI AND P3 IS UP | ORIENT P3 OF TEE TO UP (SPECIFIED DIRECTION) |
| OWN | NAVIGATE OWNER |
| GOTO OWN | GO TO OWNER OF THE SELECTED COMPONENT |
| Q ABOP/LBOP | DETAILS OF THE ARRIVE/LEAVE BOPTOM OF PIPE |
| Q ANGLE | DETAILS OF A ANGLE OF AN ELBO |
| Q ATLE | LENGTH OF FIRST TUBE OF A BRANCH |
| ATTYPE CCNN | COMMENT ATTACHMENT WITHOUT DIMENSION |
| ATTYPE CCCC | COMMENT ATTACHMENT WITH DIMENSION |
| ATTYPE XXXX | ATTA FOR SETTING THE ISOMETRIC LIMIT |
| CH CE | CHECK CURRENT ELEMENT (FOR CONSISTENCY CHECK) |
| DIR TOW NEXT ELBO | ALIGN A ELBO WITH THE NEXT ELBO |
| DIR TOW ID@ | ALIGN THE ELBOW |
| EXTEND 100 START/END | EXTEND BY 100 THE START/END OF A CROSS MEMBER |
| Q HCON/TCON | DETAILS OF HEAD/TAIL CONNECTION OF A BRANCH |
| Q HDIR | DIRECTION OF THE FLOW FROM THE BRANCH HEAD |
| Q HPOS/TPOS | DETAILS OF HEAD/TAIL POSITION OF A BRANCH |
| Q ISPE | INSULATION SPECIFICATION |
| ISPEC NULREF | FOR REMOVING INSULATION |
| SPKBRK T | FOR REMOVING INSULATION (USE IN CASE FOF ATTA) |
| LOOSE | USED BY ISODRAFT WHERE THE FLANGE IS SUPPLIED LOOSE |
| MTOC DOTD | MTO COMPONENT DOTTED WITH DIMENSION |
| MTOC DOTU | MTO COMPONENT DOTTED WITH OUT DIMENSION |
| MTOC OFF | MTO COMPONENT OFF |
| NEX CONN | NEXT CONNECT |
| NEX THRO CE | MOVE THE CURRENT COMPONENT TO NEXT |
| ORI AND P3 IS TOW ID@ & DIR TOW ID@ | ALIGNING THE 3RD P-POINT OF A TEE TOWARDS NEXT ELBOW |
| Q P3 | DETAILS OF P-POINT P3 (IN CASE OF TEE ONLY) |
| Q PA/P1 | DETAILS OF THE P-POINT 1 |
| Q PL | DERAILS OF THE P-POINT 2 |
| STEXT ‘TEXT’ | SETTING THE COMMENT TEXT |
| TCONN OPEN | TAIL CONNECTION TYPE OPEN (CE SHOULD BE BRANCH) |
| TDIR | DIRECTION OF THE FLOW FROM THE BRANCH TAIL |
| ISPEC /W | TO GIVE THE INSULATION |
| Q LBORE | TO QUERY LEAVE BORE |
| Q TBORE | TO QUERY THE TAIL BORE |
| THRO PH | THROUGH PIPE HEAD |
| THRO PREV | THROUGH PREVIOUS |
| THRO PT | THROUGH PIPE TAIL |
| Q TPOS | TO QUERY TAIL POSITION |
| Q HCON | TO QUERY THE HEAD CONNECTION |
| Q TCON | TO QUERY THE TAIL CONNECTION |
| Q ACON | TO QUERY ARRIVE CONNECTION |
| Q LCON | TO QUERY LEAVE CONNECTION |
| ATTYPE FLOW | TO CREATE FLOW DIRECTION OF ATTACHMENT |
| DIR N | DIRECTION OF COMPONENT TOWARDS NORTH |
| BACK CONN | BACKWARD CONNECTION |
| MTOC UNSET | TO FREEZE THE COMPONENT FROM MTO REPORT |
Above mention PDMS piping commands are very useful while do the modeling piping in E3d. These pdms Piping commands helps to enhance the speed of the work on E3D software. Users have to use these above e3d piping commands while working on the piping module of E3D. You ca also refer the E3D Equipment modeling commands and PDMS draft commands from these sources.
3 thoughts on “PDMS piping commands”